Description

This pH sensor is commonly used to test the pH of a liquid as it measures the hydrogen-ion activity in water-based solutions. Wherever acidity and alkalinity testing is required, it is frequently employed in the chemical businesses, pharmaceutical industry, dye industry, and
scientific research. This kit’s drive board works with both 9V systems. It’s also very easy to work with Arduino and Raspberry Pi.
It can be used in a variety of PH measurements with fast response and excellent thermal stability. It has good reproducibility, and can eliminate basic alkali errors. In 0pH to 14pH range, the output voltage is linear. The reference system which consists of the Ag/AgCl gel electrolyte salt bridge has a stable half-cell potential and excellent anti-pollution performance. The ring PTFE membrane is not easy to clog, so the electrode is suitable for long-term online detection

Features: Ph Sensor Module

1. This pH sensor is a piece of equipment used in science to determine whether a solution is naturally acidic or alkaline
2. pH levels can be detected between 0 and 14 by the sensor set
3. This pH sensor kit can be used to assess the quality of both soil and water
4. As part of the sensor package, a pH probe and sensor board will be used to condition the signal

Specification: PH Sensor Module Kit

Module Power: DC 9.00V 1A
Measuring Range: 0-14PH
Accuracy: ± 0.1pH (24 )
Response Time: 1min
Industry pH Electrode with BNC Connector
PH Interface (2-foot patch )
Power Indicator LED
Output: Analog values in the range of (0.5V to 3V)
Alkali Error: 0.2PH
Internal Resistance: 250MO
Response Time: <1min
Operating Temperature: 0-60°
Terminal Blocks: BNC plug
BNC Connector is suitable for most PH meters and controllers.
Suitable for a wide range of applications: Aquariums, Hydroponics, Laboratory, etc.
This PH sensor is calibrated @ 24 degrees centigrade room temperature. Calibrated values are: PH4 = 1.5V, PH7 = 2.0V and PH9 = 2.5V

Applications: PH Sensor Module with Electrode Probe

Water quality testing
Aquaculture

Cautions: Ph Sensor Module

Before being measured, the electrode must be calibrated with a standard buffer solution of known pH value. In order to obtain more accurate results, the known PH value should be reliable, and closer to the measured one.
When the measurement is completed, the electrode protective sleeve should be put on. A small amount of 3.3mol / L potassium chloride solution should be placed in the protective sleeve to keep the electrode bulb wet.
The leading end of the electrode must be kept clean and dry to prevent short circuits at both ends of the output, otherwise, it will lead to inaccurate or invalid measurement results.
After long-term use of the electrode, if you find that the gradient is slightly inaccurate, you can soak the lower end of the electrode in 4% HF (hydrofluoric acid) for 3-5 seconds, wash it with distilled water, and then soak in potassium chloride solution to make it new.

Activation: Ph Sensor Module

pH/REF – Soak the glass bulb and ceramic junction in 0.1M Hydrochloric Acid for 2 hours and then rinse thoroughly with distilled water
ORP – Electrodes may need additional cleaning occasionally with polishing paper
Conductivity cell – Replating is required if the mentioned cell constants are not obtained

Probe Specification:

Measuring range :- 0~14pH
Resolution :- 0.01pH
% Theoretical slope :- (PTS) ≥98.5% (25 ℃)
Probe length :- 1 meter
Resistance :- ≤250MΩ (25 ℃)
Alkali error :- ≤15mV (25 ℃)
Ambient Temp. (Operating) :- 0ºC~80ºC (32ºF~152ºF)
Relative humidity (Operating) :- ≤85%

NOTE: Maintenance and precautions:

1. Test before removing the electrode protective sleeve (kit solution is 3MKCL, if there are crystals oozing is normal and does not affect the use of electrodes)
2. Observe whether all sensitive bulb filled with liquid inside, if there is a bubble, you should gently shake the electrode downward (like rejection thermometer) to remove air bubbles inside the sensitive bulb, otherwise it will affect test accuracy.

How to Use the pH Meter / PH sensor Module:

Sample Code – Check Here
Tutorial Video – Check Here

It can be used in a variety of PH measurements with fast response and excellent thermal stability. It has good reproducibility, and can eliminate basic alkali errors. In 0pH to 14pH range, the output voltage is linear. The reference system which consists of the Ag/AgCl gel electrolyte salt bridge has a stable half-cell potential and excellent anti-pollution performance. The ring PTFE membrane is not easy to clog, so the electrode is suitable for long-term online detection.

ADIY analog pH sensor, specially designed for Arduino controllers is easy to use and can be used as a plug-and-play solution to measure the pH value of a solution without any additional circuit required. Instant connection to your probe and Arduino to get pH measurements at ± 0.1pH (25 ?). For most hobbyists, this great accuracy range and its low cost make this a great tool for bio-robotics and other projects! It has an LED that works as the Power Indicator, a BNC connector, and a PH2.0 sensor interface. To use it, connect the pH sensor with the BND connector, and plug the PH2.0 interface into the analog input port of any Arduino controller. You will get the pH value easily with a simple program to a ready analog voltage. Comes in a compact plastic box with foams for better mobile storage. Build your own PH meter gadget or a water monitoring station for your water tanks. This and our other water sensor devices could make for the ultimate water control device. Use it for your aquaponics or fish tanks or other materials that need measurements.

Need to measure water quality and other parameters but haven’t got any low-cost pH meter? Find it difficult to use Arduino? Our analog pH meter is specially designed for Arduino controllers and has a convenient and practical connector and a bunch of features. Instant connection to your probe and Arduino to get pH measurements at ± 0.1pH (25 ?). For most hobbyists, this great accuracy range and its low cost make this a great tool for bio-robotics and other projects! It has an LED that works as the Power Indicator, a BNC connector and a PH2.0 sensor interface. To use it, connect the pH sensor with the BND connector, and plug the PH2.0 interface into the analog input port of any Arduino controller. If pre-programmed, you will get the pH value easily. Comes in a compact plastic box with foams for better mobile storage. Build your own PH meter gadget or a water monitoring station for your water tanks. This and our other water sensor devices could make for the ultimate water control device. Use it for your aquaponics or fish tanks or other materials that need measurements. Note: buffer solutions are not included.

Cautions:

Please use an external switching power supply, and the voltage as close as possible to the +5.00V. More accurate the voltage, the higher the accuracy!
Before the electrode in continuously used every time, you need to calibrate it with the standard solution, in order to obtain more accurate results. The best environment temperature is about 25, and the pH value is known and reliable, close to the measured value. If you measure the acidic sample, the pH value of the standard solution should be 4.00. If you measure the alkaline sample, the pH value of the standard solution should be 9.18. Subsection calibration, just in order to get better accuracy.
Before the pH electrode measured different solutions, we need to use water to wash it. We recommend using deionized water.
Connect equipment according to the graphic, that is, the pH electrode is connected to the BNC connector on the pH meter board, and then use the connection lines, the pH meter board is connected to the analog port 0 of the Arduino controller. When the Arduino controller gets power, you will see the blue LED on the board is on.
Upload the sample code to the Arduino controller. (Sample Code – Check Here )
Put the pH electrode into the standard solution whose pH value is 7.00 or directly shorted the input of the BNC connector. Open the serial monitor of the Arduino IDE, and you can see the pH value printed on it, and the error does not exceed 0.3. Record the pH value printed, then compared it with 7.00, and the difference should be changed into the Offset in the sample code. For example, the pH value printed is 6.88, so the difference is 0.12. You should change the # define Offset 0.00 into # define Offset 0.12 in your program.
Put the pH electrode into the pH standard solution whose value is 4.00. Then wait about one minute, adjust the gain potential device, let the value stabilize at around 4.00. At this time, the acidic calibration has been completed and you can measure the pH value of an acidic solution.

Note: If you want to measure the pH value of other solutions, you must wash the pH electrode first!

-44%

Click to enlarge

Ph Sensor Module with Ph Probe

Original price was: ₹2,770.00.Current price is: ₹1,549.00. (Including GST)

Ph Sensor Module with Ph electrode Probe by ADIY Also Known as Analog pH Sensor Kit is specially designed for Arduino controllers. This pH sensor is commonly used to test the pH of a liquid as it measures the hydrogen-ion activity in water-based solutions. Wherever acidity and alkalinity testing is required, it is frequently employed in the chemical businesses, pharmaceutical industry, dye industry, and scientific research. This kit’s drive board works with both 9V systems. It’s also very easy to work with Arduino and Raspberry Pi.